CVE, singkatan dari Common Vulnerabilities and Exposures, adalah daftar kerentanan keamanan komputer yang telah diungkapkan kepada publik.
OWASP
OWASP Top 10 adalah inisiatif yang mengidentifikasi dan mendokumentasikan 10 kerentanan keamanan teratas dalam aplikasi web.
CISA KEV
CISA Known Exploited Vulnerabilities (KEV) adalah inisiatif yang mengidentifikasi dan mempublikasikan daftar kerentanan yang diketahui telah dieksploitasi.
CPE, singkatan dari Common Platform Enumeration, adalah skema standar untuk penamaan perangkat keras, perangkat lunak, dan sistem operasi. CPE menyediakan skema penamaan terstruktur untuk mengidentifikasi dan mengklasifikasikan sistem teknologi informasi, platform, dan paket secara unik berdasarkan atribut tertentu seperti vendor, nama produk, versi, pembaruan, edisi, dan bahasa.
CWE, atau Common Weakness Enumeration, adalah daftar dan kategorisasi komprehensif tentang kelemahan dan kerentanan perangkat lunak. Ini berfungsi sebagai bahasa umum untuk mendeskripsikan kelemahan keamanan perangkat lunak dalam arsitektur, desain, kode, atau implementasi yang dapat menyebabkan kerentanan.
CAPEC, singkatan dari Common Attack Pattern Enumeration and Classification, adalah sumber daya publik yang komprehensif yang mendokumentasikan pola serangan umum yang digunakan oleh penyerang dalam serangan siber. Basis pengetahuan ini bertujuan untuk memahami dan mengartikulasikan kerentanan umum dan metode yang digunakan penyerang untuk mengeksploitasinya.
Layanan & Harga
Bantuan & Info
Cari : CVE id, CWE id, CAPEC id, vendor atau kata kunci dalam CVE
In the Linux kernel, the following vulnerability has been resolved:
idpf: disable DIM work before freeing q_vectors
idpf never drains the Tx/Rx DIM works before freeing the memory they
live in. tx_dim and rx_dim are embedded in struct idpf_q_vector, they
are queued from the NAPI poll via net_dim(), and idpf_vport_intr_rel()
ends with kfree(rsrc->q_vectors). Nothing in the driver cancels them.
idpf_tx_dim_work() and idpf_rx_dim_work() then run on freed memory:
idpf_vport_intr_write_itr() writes the ITR register through
q_vector->intr_reg.tx_itr / rx_itr, void __iomem pointers loaded out of
the freed q_vector. No configuration is needed to get there --
IDPF_ITR_IS_DYNAMIC() is defined as (itr_mode) and idpf_vport_alloc()
initialises both modes to IDPF_ITR_DYNAMIC.
Draining after idpf_vport_intr_napi_dis_all() is not enough on its own.
idpf_net_dim() is called from inside the
"if (napi_complete_done(napi, work_done))" branch of the poll, and
napi_complete_done() has already cleared NAPIF_STATE_SCHED by then.
napi_disable_locked() waits only while (val & (NAPIF_STATE_SCHED |
NAPIF_STATE_NPSVC)), so napi_disable() can return while the poll tail is
still queueing the work, and a plain cancel_work_sync() would be
re-armed behind the drain.
Use disable_work_sync(): schedule_work() on a work with a non-zero
disable count is dropped by clear_pending_if_disabled() before
__queue_work() is reached.
Move idpf_init_dim() to idpf_vport_intr_alloc() so the works are
initialised on every path that can reach the drain -- the three
"goto intr_deinit" sites between idpf_vport_intr_init() and
idpf_vport_intr_ena() get there without the enable side having run.
Nothing re-enables them: rsrc->q_vectors is freed on every exit from
idpf_vport_open() and on every idpf_vport_stop(), so the count dies with
the object.
It is a race, not a deterministic failure -- net_dim() only schedules
once DIM_NEVENTS events have accumulated and the profile index changes.
A KASAN ifup/ifdown loop under load is the way to see it.