CVE, singkatan dari Common Vulnerabilities and Exposures, adalah daftar kerentanan keamanan komputer yang telah diungkapkan kepada publik.
OWASP
OWASP Top 10 adalah inisiatif yang mengidentifikasi dan mendokumentasikan 10 kerentanan keamanan teratas dalam aplikasi web.
CISA KEV
CISA Known Exploited Vulnerabilities (KEV) adalah inisiatif yang mengidentifikasi dan mempublikasikan daftar kerentanan yang diketahui telah dieksploitasi.
CPE, singkatan dari Common Platform Enumeration, adalah skema standar untuk penamaan perangkat keras, perangkat lunak, dan sistem operasi. CPE menyediakan skema penamaan terstruktur untuk mengidentifikasi dan mengklasifikasikan sistem teknologi informasi, platform, dan paket secara unik berdasarkan atribut tertentu seperti vendor, nama produk, versi, pembaruan, edisi, dan bahasa.
CWE, atau Common Weakness Enumeration, adalah daftar dan kategorisasi komprehensif tentang kelemahan dan kerentanan perangkat lunak. Ini berfungsi sebagai bahasa umum untuk mendeskripsikan kelemahan keamanan perangkat lunak dalam arsitektur, desain, kode, atau implementasi yang dapat menyebabkan kerentanan.
CAPEC, singkatan dari Common Attack Pattern Enumeration and Classification, adalah sumber daya publik yang komprehensif yang mendokumentasikan pola serangan umum yang digunakan oleh penyerang dalam serangan siber. Basis pengetahuan ini bertujuan untuk memahami dan mengartikulasikan kerentanan umum dan metode yang digunakan penyerang untuk mengeksploitasinya.
Layanan & Harga
Bantuan & Info
Cari : CVE id, CWE id, CAPEC id, vendor atau kata kunci dalam CVE
In the Linux kernel, the following vulnerability has been resolved:
i2c: xiic: restore non-managed runtime PM to fix clk WARN flood
The devres conversion replaced manual pm_runtime_enable()/disable() with
devm_pm_runtime_set_active_enabled() and dropped the remove-time runtime
PM teardown. The managed release tears runtime PM down in the wrong
order: it calls pm_runtime_dont_use_autosuspend() before
pm_runtime_disable(), i.e. while runtime PM is still enabled, and devres
is LIFO so the devm_clk_get_enabled() release runs afterwards.
At remove(), pm_runtime_put_sync() leaves the device active with the
autosuspend timer armed. Clearing use_autosuspend then makes rpm_idle()
suspend immediately, and xiic_i2c_runtime_suspend() clk_disable()s the
clock. The later devm_clk_get_enabled() release clk_disable_unprepare()s
the already-disabled clock, so clk_core_disable() WARNs ("clkN already
disabled") on every teardown.
Drop the managed helper and restore the non-managed runtime PM setup and
teardown, so runtime PM is enabled once in probe and disabled once in
remove and the clock enable count stays balanced.
Order the remove teardown so runtime PM is disabled before the usage
count is dropped: pm_runtime_disable() followed by pm_runtime_put_noidle()
instead of pm_runtime_put_sync(). Dropping the count first with autosuspend
still enabled arms the autosuspend timer, and a preemption before
pm_runtime_disable() lets it expire, suspend the device and clk_disable()
the clock, which the devm release then disables again - the same WARN.
Restore the non-managed IRQ request as well. The probe error paths now
unwind runtime PM by hand via goto, and a devm-registered handler is only
freed later during devres unwind, so it would stay live across the manual
teardown (and across any future failing step added after it). Request the
IRQ with request_threaded_irq() and free it explicitly in the probe error
path and in remove. The probe error path also clears use_autosuspend, to
match the teardown in remove().