CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Bump asid_generation on CPU online to avoid ASID collision after hotplug
If a vCPU stays scheduled out (or blocked) while the last pCPU it ran
on goes through a hotplug cycle (online->offline->online), and the vCPU
then resumes execution on the same pCPU, then it is possible for it to
run with an ASID that has now been assigned to a different vCPU,
resulting in stale TLB translations being used.
svm_enable_virtualization_cpu() resets asid_generation to 1 and sets
next_asid to max_asid + 1 on every CPU online event, including hotplug
cycles. Because next_asid starts beyond the pool boundary, the first
call to new_asid() after an online event always wraps the pool,
incrementing asid_generation to 2 and assigning ASIDs starting from
min_asid.
Consider two vCPUs from different VMs, vCPU-A pinned to CPU-X holding
asid_generation=2 and ASID=N from before the hotplug event:
1. CPU-X goes offline and back online: asid_generation resets to 1,
next_asid = max_asid + 1.
2. One or more vCPUs migrate to CPU-X and call new_asid(), wrapping
the pool and consuming ASIDs starting from min_asid. Eventually
vCPU-B from a different VM is assigned asid_generation=2, ASID=N
— the same ASID that vCPU-A held before the hotplug.
3. vCPU-A enters pre_svm_run() on CPU-X: current_vmcb->cpu is
unchanged so the migration branch is skipped. Its saved
asid_generation=2 matches sd->asid_generation=2, so the generation
check silently passes and vCPU-A continues running with ASID=N —
the same ASID just freshly assigned to vCPU-B.
Both vCPUs from different VMs now run on CPU-X with the same ASID,
causing them to share NPT TLB entries and producing stale translations.
The collision manifests as a KVM internal error (Suberror: 1, emulation
failure). The NPT page fault reports a faulting GPA far outside the
VM's physical memory range — a sign of stale TLB translations being
used. KVM falls back to instruction emulation, which fails on
FPU/XSave instructions (XRSTOR, STMXCSR) that the emulator does not
implement.
Fix this by incrementing asid_generation instead of resetting it to 1
in svm_enable_virtualization_cpu(). On module load, asid_generation
starts at 0 (memset) and the increment produces 1, identical to the
old behaviour. On subsequent hotplug cycles the generation advances
beyond any value a vCPU previously observed on this CPU, so the
generation check in pre_svm_run() reliably forces new_asid() on every
vCPU after every hotplug cycle.