CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
udf: Mark LVID buffer as uptodate before marking it dirty
When an I/O error occurs while writing the Logical Volume Integrity
Descriptor (LVID) buffer to the block device, the block layer's completion
handler (`end_buffer_write_sync()`) clears the `BH_Uptodate` flag on the
buffer. However, the buffer still contains valid LVID data in memory. If
the filesystem is subsequently remounted read-write or synced,
`udf_open_lvid()` or `udf_sync_fs()` will modify the LVID buffer and call
`mark_buffer_dirty()`. This triggers a spurious
`WARN_ON_ONCE(!buffer_uptodate(bh))` warning in `mark_buffer_dirty()`
because the buffer is not marked uptodate, even though its in-memory
contents are valid and are about to be overwritten.
To prevent this spurious warning, unconditionally set the `BH_Uptodate`
flag before calling `mark_buffer_dirty()` in `udf_open_lvid()` and
`udf_sync_fs()`. This acknowledges that the in-memory buffer is valid and
matches the workaround previously applied to `udf_close_lvid()` in commit
853a0c25baf9 ("udf: Mark LVID buffer as uptodate before marking it dirty").
Extending this workaround ensures consistent behavior across all LVID
updates.
Buffer I/O error on dev loop0, logical block 128, lost sync page write
------------[ cut here ]------------
!buffer_uptodate(bh)
WARNING: fs/buffer.c:1087 at mark_buffer_dirty+0x299/0x410 fs/buffer.c:1087
...
Call Trace:
udf_open_lvid+0x369/0x5b0 fs/udf/super.c:2078
udf_reconfigure+0x336/0x540 fs/udf/super.c:679
reconfigure_super+0x232/0x8f0 fs/super.c:1080
vfs_cmd_reconfigure fs/fsopen.c:268 [inline]
vfs_fsconfig_locked+0x171/0x320 fs/fsopen.c:297
__do_sys_fsconfig fs/fsopen.c:463 [inline]
__se_sys_fsconfig+0x6b9/0x810 fs/fsopen.c:350
do_syscall_64+0x174/0x580 arch/x86/entry/syscall_64.c:94