CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: use skb_get() instead of skb_clone() for req_skb
BT enable fails intermittently with -ETIMEDOUT (-110). The kernel log
shows the HCI Read Local Version command was sent and the firmware
replied with status 0x00 (logged by hci_req_cmd_complete() BT_DBG),
but the waiter in __hci_cmd_sync_sk() never woke up and timed out
after 10 s:
bluetooth hci0: Opcode 0xfc00 // __hci_cmd_sync_sk
bluetooth hci0: opcode 0xfc00 plen 1 // hci_cmd_sync_add
bluetooth hci0: skb len 4 // hci_cmd_sync_alloc
bluetooth hci0: length 1 // hci_req_sync_run
Bluetooth: hci0 cmd_cnt 1 cmd queued 1 // hci_cmd_work
Bluetooth: hci0 type 1 len 4 // hci_send_frame
Bluetooth: opcode 0xfc00 status 0x00 // hci_req_cmd_complete
<-- req_skb NULL: req_complete_skb not set,
hci_cmd_sync_complete() never called,
req_status stays HCI_REQ_PEND -->
<-- 10 s later: wait_event_interruptible_timeout expires -->
bluetooth hci0: end: err -110 // __hci_cmd_sync_sk
The root cause is that hci_send_cmd_sync() clones the sent command
into hdev->req_skb so that hci_req_cmd_complete() can locate the
registered completion callback. Under memory pressure this
skb_clone() fails, leaving hdev->req_skb NULL. The firmware reply
is received and processed, but hci_req_cmd_complete() finds NULL
req_skb, so hci_cmd_sync_complete() is never called, req_status
stays HCI_REQ_PEND, and the waiter times out with -ETIMEDOUT.
req_skb is only used to read bt_cb(skb)->hci callbacks and opcode --
it is never modified. Replace skb_clone() with skb_get(), which
simply increments the reference count of hdev->sent_cmd without
allocating new memory and therefore cannot fail.
This issue was first observed as a use-after-free in ttyport_close()
when ttyport_open() failed, which was investigated in an earlier
patch series [1]. That investigation led to the discovery of the
true root cause described above.
[1] https://lore.kernel.org/all/20250430111617.1151390-1-quic_cxin@quicinc.com/