CVE-2026-98395
2026-10-14
14h17 +00:00
14h17 +00:00
Thông báo cho một CVE
Luôn được thông báo về mọi thay đổi đối với một CVE cụ thể.
Mô tả CVE
In the Linux kernel, the following vulnerability has been resolved:
powerpc/entry: Fix irq_soft_mask corruption on replayed interrupt exit
When __replay_soft_interrupts() replays a pending interrupt (e.g.
PACA_IRQ_DEC -> timer_interrupt), it calls the handler directly with a
synthetic pt_regs. The DEFINE_INTERRUPT_HANDLER_ASYNC wrapper around
each handler calls arch_interrupt_async_exit_prepare() on the way out,
which calls arch_interrupt_exit_prepare() -> local_irq_disable() ->
arch_local_irq_disable(), which does:
irq_soft_mask_set(IRQS_DISABLED) /* 0x1 */
This unconditionally overwrites irq_soft_mask with IRQS_DISABLED (0x1),
stripping the IRQS_PMI_DISABLED (0x2) bit. The result is that
irq_soft_mask is 0x1 instead of IRQS_ALL_DISABLED (0x3) when the
handler returns to __replay_soft_interrupts().
For a normally-taken interrupt this is harmless: the next interrupt
always enters through arch_interrupt_enter_prepare() which
unconditionally sets irq_soft_mask to IRQS_ALL_DISABLED. But during
replay, next_interrupt() is called directly between replayed handlers
without going back through arch_interrupt_enter_prepare(), so the
stripped bit is never restored. next_interrupt() then fires a WARNING:
WARNING: arch/powerpc/kernel/irq_64.c:75
WARN_ON(irq_soft_mask_return() != IRQS_ALL_DISABLED)
The warning was observed early in boot on a POWER10 pseries guest
during kmem_cache_init_late(), where a spinlock release triggers
interrupt replay that processes a pending timer interrupt.
Debugger state confirming the bug:
Before timer_interrupt(®s):
irq_soft_mask = 0x3 (IRQS_ALL_DISABLED) correct
irq_happened = 0x41 (HARD_DIS|REPLAYING) correct
After timer_interrupt(®s) returns:
irq_soft_mask = 0x1 (IRQS_DISABLED) WRONG - PMI bit stripped
irq_happened = 0x41 unchanged
The fix is to replace local_irq_disable() with hard_irq_disable().
hard_irq_disable() is the right primitive here for two reasons:
1. On PPC64 (hw_irq.h:301) it calls irq_soft_mask_set_return(IRQS_ALL_DISABLED),
setting the soft mask to 0x3 (both IRQS_DISABLED and IRQS_PMI_DISABLED),
which preserves the PMI bit and fixes the WARNING. The additional
work it does (__hard_irq_disable(), PACA_IRQ_HARD_DIS |=) is
redundant but safe since both are already set at this point in the
exit path; the trace_hardirqs_off() inside is guarded by
if (!arch_irqs_disabled_flags(flags)) so it will not double-fire.
2. On PPC32 (hw_irq.h:467) hard_irq_disable() maps to
arch_local_irq_disable() -> __hard_irq_disable(), which clears
MSR[EE] in hardware. This is exactly correct: PPC32 has no soft-mask
PACA mechanism, so the hardware disable is the right way to satisfy
irqentry_exit()'s requirement. This also fixes a build error on PPC32
where irq_soft_mask_set() is only defined under CONFIG_PPC64:
arch/powerpc/include/asm/entry-common.h:273: error: implicit
declaration of function 'irq_soft_mask_set'
Using hard_irq_disable() requires no #ifdef and is consistent with
how the rest of the entry code (e.g. entry-common.h:463) handles the
same PPC32/PPC64 split.
