CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
net: icmp: avoid invalid transport header access in icmp_send tracepoint
syzbot reported a WARNING triggered by DEBUG_NET_WARN_ON_ONCE():
WARNING: at skb_transport_header include/linux/skbuff.h:3087 [inline]
WARNING: at udp_hdr include/linux/udp.h:23 [inline]
WARNING: at do_trace_event_raw_event_icmp_send include/trace/events/icmp.h:30 [inline]
WARNING: at trace_event_raw_event_icmp_send+0x48c/0x6ec include/trace/events/icmp.h:11
Call trace:
skb_transport_header include/linux/skbuff.h:3087 [inline]
udp_hdr include/linux/udp.h:23 [inline]
do_trace_event_raw_event_icmp_send include/trace/events/icmp.h:30 [inline]
trace_event_raw_event_icmp_send+0x48c/0x6ec include/trace/events/icmp.h:11
__traceiter_icmp_send include/trace/events/icmp.h:11 [inline]
__do_trace_icmp_send include/trace/events/icmp.h:11 [inline]
trace_icmp_send+0x320/0x49c include/trace/events/icmp.h:11
__icmp_send+0xcfc/0x11d8 net/ipv4/icmp.c:1013
ipv4_send_dest_unreach net/ipv4/route.c:1280 [inline]
ipv4_link_failure+0x57c/0x8dc net/ipv4/route.c:1287
dst_link_failure include/net/dst.h:438 [inline]
vti_tunnel_xmit+0xe40/0x17a4 net/ipv4/ip_vti.c:307
TP_fast_assign() unconditionally calls udp_hdr(skb) before checking
whether the packet is UDP. Furthermore, __icmp_send() can be invoked
from paths (e.g., link failures, ARP errors, forwarding, AF_PACKET)
where skb->transport_header was never initialized (~0U).
Under CONFIG_DEBUG_NET=y, calling skb_transport_header(skb) triggers
DEBUG_NET_WARN_ON_ONCE(!skb_transport_header_was_set(skb)).
Fix this by:
1. Only parsing transport info when iph->protocol == IPPROTO_UDP.
2. Using skb_header_pointer() at skb_network_offset(skb) + (iph->ihl << 2)
to safely fetch the UDP header without assuming transport_header is set.