CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
drm/client: fix restore of partially initialized client
I got a null-ptr-deref report when closing a DRM file descriptor:
WARNING: drivers/gpu/drm/drm_atomic.c:2031 at
__drm_atomic_helper_set_config+0x18e/0x1b0 [drm]
Call Trace:
drm_client_modeset_commit_atomic+0x16b/0x220 [drm]
drm_client_modeset_commit_locked+0x56/0x160 [drm]
drm_client_modeset_commit+0x21/0x40 [drm]
__drm_fb_helper_restore_fbdev_mode_unlocked.part.0+0x7b/0x80
drm_fbdev_client_restore+0xe/0x20 [drm_client_lib]
drm_client_dev_restore+0x9f/0xc0 [drm]
drm_release+0xc5/0xe0 [drm]
The warning is followed by a NULL pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP:
__drm_fb_helper_restore_fbdev_mode_unlocked.part.0+0x41/0x80
[drm_kms_helper]
Call Trace:
drm_fbdev_client_restore+0xe/0x20 [drm_client_lib]
drm_client_dev_restore+0x9f/0xc0 [drm]
drm_release+0xc5/0xe0 [drm]
__fput+0xdc/0x2b0
__x64_sys_close+0x39/0x80
do_syscall_64+0x8d/0x460
entry_SYSCALL_64_after_hwframe+0x76/0x7e
drm_client_register() adds the DRM client to the device client list
before invoking the initial hotplug callback. If the hotplug callback
fails, the client remains registered.
For the fbdev client, a failure during drm_fb_helper_initial_config()
causes the partially initialized fbdev helper to be cleaned up.
drm_fb_helper_fini() releases fb_helper->info and leaves it NULL.
The fbdev client therefore remains registered even though there is no
fully initialized framebuffer device.
Later, when userspace closes the DRM file descriptor, drm_release()
can invoke the restore callbacks of registered DRM clients:
drm_release()
drm_client_dev_restore()
drm_fbdev_client_restore()
drm_fb_helper_restore_fbdev_mode_unlocked()
drm_fbdev_client_restore() currently restores the fbdev state
unconditionally. For a partially initialized fbdev client this can
submit an incomplete modeset state and subsequently access fbdev
state which has not been initialized, resulting in the warning and
NULL pointer dereference above.
drm_fbdev_client_unregister() already uses fb_helper->info to
distinguish a fully probed framebuffer device from a partially
initialized client.
Use the same condition in drm_fbdev_client_restore() and skip restore
if no framebuffer device has been successfully initialized.