CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix rx Scatter-Gather support
When a received frame is larger than dma_buf_sz, the DMA scatters it
across multiple RX descriptors (rx Scatter-Gather). The secondary RX
buffer (sec_page) was only allocated and programmed when split-header
(SPH) was active, so for regular frames buffer2 was neither allocated
nor backed by a valid mapping. As soon as an incoming frame overflowed
buffer1, the DMA wrote the overflow into the unmapped secondary-buffer
address, triggering an SMMU translation fault on IOMMU-based platforms:
arm-smmu 15000000.iommu: Unhandled context fault: fsr=0x402, iova=0x00000000, fsynr=0x7f0011, cbfrsynra=0x1c90, cb=11
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x1c90
arm-smmu 15000000.iommu: FSYNR0 = 007f0011 [S1CBNDX=127 WNR PLVL=1]
Enable scatter-gather for non-SPH frames on cores that can program an
independent secondary RX buffer (GMAC4/XGMAC): allocate and mark buffer2
as valid in stmmac_init_rx_buffers() and stmmac_rx_refill(), and account
for it in the buffer length computation. Legacy cores have no set_sec_addr
op, so they keep buffer2 disabled.
Since buffer2 is handed to the DMA at page offset 0, the page pool sync
window is widened to cover both buffers in every mode: offset is set to 0
and max_len to dma_buf_sz + stmmac_rx_offset().
The FCS can straddle the buffer1/buffer2 boundary and a descriptor
boundary, so it is now stripped from the tail of the assembled frame with
pskb_trim() instead of from a single buffer, avoiding an unsigned underflow
for frames that overflow a buffer by 1..3 bytes. For single-buffer frames
the XDP program must not see the FCS, so it is removed from the XDP buffer
before the program runs.
Native XDP currently only supports single-buffer (linear) frames. An
oversized frame accepted by the MAC (jumbo enabled) is received via
buffer2; the XDP program only sees buffer1, so on a TX/REDIRECT verdict
the frame is forwarded truncated. XDP multi-buffer support to handle
this case is planned as a follow-up.
AF_XDP zero-copy RX is not covered by this change: a ZC queue still
programs buffer2 at DMA address 0 (and XGMAC has no buffer2-valid bit),
so an oversized frame overflowing buffer1 can still trigger the same
SMMU translation fault. Handling is planned as a follow-up.