CPE, viết tắt của Liệt kê nền tảng phổ biến, là một lược đồ đặt tên chuẩn hóa cho phần cứng, phần mềm và hệ điều hành. CPE cung cấp lược đồ đặt tên có cấu trúc để xác định và phân loại duy nhất các hệ thống công nghệ thông tin, nền tảng và gói phần mềm dựa trên các thuộc tính nhất định như nhà cung cấp, tên sản phẩm, phiên bản, cập nhật, phiên bản và ngôn ngữ.
CWE, hay Liệt kê điểm yếu phổ biến, là danh sách và phân loại toàn diện các điểm yếu và lỗ hổng phần mềm. Nó phục vụ như ngôn ngữ chung để mô tả các điểm yếu bảo mật phần mềm trong kiến trúc, thiết kế, mã hoặc triển khai có thể dẫn đến lỗ hổng.
CAPEC, viết tắt của Liệt kê và phân loại mẫu tấn công phổ biến, là tài nguyên toàn diện, có sẵn công khai ghi lại các mẫu tấn công phổ biến được đối thủ sử dụng trong các cuộc tấn công mạng. Cơ sở kiến thức này nhằm mục đích hiểu và diễn đạt các lỗ hổng phổ biến và các phương pháp kẻ tấn công sử dụng để khai thác chúng.
Dịch vụ và giá cả
Trợ giúp và thông tin
Tìm kiếm: ID CVE, ID CWE, ID CAPEC, nhà cung cấp hoặc từ khóa trong CVE
In the Linux kernel, the following vulnerability has been resolved:
fs: avoid repeated scans in evict_inodes()
We observed hung tasks when users attempted to unmount a filesystem
after its disk had been removed while still in use. During device
removal, fs_bdev_mark_dead() calls evict_inodes() while holding s_umount.
Each time evict_inodes() drops s_inode_list_lock to reschedule, it
restarts the walk from the head of s_inodes. With many referenced inodes
at the head of the list, these restarts repeatedly scan the same inodes
without reclaiming them. This can keep s_umount held for a long time,
blocking concurrent umount attempts and triggering hung-task reports.
Keep the current inode, already marked I_FREEING, out of the disposal
batch until s_inode_list_lock is reacquired. Resume the walk from this
inode and dispose of it in a later batch or at the end of the walk.
The zero-refcount and state checks under i_lock allow this walker to
claim the inode by setting I_FREEING and removing it from the LRU.
Other reclaimers skip the inode, leaving this walker responsible for
eviction. Only evict() removes it from s_inodes, so keeping it out of
the disposal batch ensures that it remains on the list while the lock
is dropped. After reacquiring the lock, reading its current next pointer
accounts for concurrent removal of following inodes.
The existing inode lifetime rules prohibit acquiring a reference to an
inode marked I_FREEING or I_WILL_FREE. __iget() requires its caller to
hold i_lock and establish that taking a reference is valid. Inode lookup
and igrab() check these flags under i_lock when acquiring a reference
from zero. ihold() requires an existing reference, which would keep
i_count nonzero and prevent this walker from claiming the inode. These
rules already allow iput_final() and the inode shrinker to release
i_lock after setting I_FREEING and before eviction completes.
A temporary __iget() reference would also keep the inode on the list,
but its release must preserve last-reference handling. Another user can
acquire a reference, update lazy timestamps and drop its reference while
the pin is held. If the pin becomes the last reference, dropping it with
atomic_dec_and_test() and evicting directly bypasses iput()'s lazytime
handling and can lose those timestamp updates.
Releasing the pin with iput() preserves that handling, but does not
guarantee eviction. fs_bdev_mark_dead() runs with SB_ACTIVE set, so iput()
may retain the inode in cache, whereas evict_inodes() must evict eligible
zero-reference inodes. The inode may also have been freed when iput()
returns, so the walker cannot then use it to force eviction. Using
I_FREEING preserves the existing eviction behavior without introducing
an additional last-reference transition.
The xfstests auto group passed on ext4 and XFS with known unrelated
failures excluded. No new issues were observed, and the previously
reproducible hung task no longer occurs with this patch.